OEM/ODM China H13 Tool Steel | 1.2344 | X40CrMoV5-1 | SKD61 Hot Work Steel Supply to Cairo

OEM/ODM China
 H13 Tool Steel | 1.2344 | X40CrMoV5-1 | SKD61 Hot Work Steel Supply to Cairo

Short Description:

H13 Tool Steel is chromium hot work tool steels which are widely used in hot and cold work tooling applications. H13 tool steel is classified as group H steels by the AISI classification system. This series of steels start from H1 to H19. AISI H-13 tool steel is characterized by: Good resistance to abrasion at both low and high temperatures High level of toughness and ductility Uniform and high level of machinability and polishability Good high-temperature strength and resistance to t...


  • Length: 3-5.8mm or Customization
  • Surface: black, peeled, or rough turned
  • Heat treatment: air-cooling, normalized, annealed, Q&T
  • Smelting process: EAF+LF+VD
  • Product Detail

    Product Tags

    Our company puts emphasis on the management, the introduction of talented personnel, and the construction of staff building, trying hard to improve the quality and liability consciousness of staff members. Our company successfully attained IS9001 Certification and European CE Certification of OEM/ODM China H13 Tool Steel | 1.2344 | X40CrMoV5-1 | SKD61 Hot Work Steel Supply to Cairo, We are confident to make great achievements in the future. We are looking forward to becoming one of your most reliable suppliers.


    H13 Tool Steel is chromium hot work tool steels which are widely used in hot and cold work tooling applications. H13 tool steel is classified as group H steels by the AISI classification system. This series of steels start from H1 to H19.

    AISI H-13 tool steel is characterized by:

    • Good resistance to abrasion at both low and high temperatures

    • High level of toughness and ductility

    • Uniform and high level of machinability and polishability

    • Good high-temperature strength and resistance to thermal fatigue

    • Excellent through-hardening properties

    • Very limited distortion during hardening

    In
    steel H13, the molybdenum and vanadium act as strengthening agents. The
    chromium content assists die steel H-13 to resist softening when used
    at high temperatures. H-13 die steels offers an excellent combination of
    shock and abrasion resistance, and possesses good red hardness. It is
    capable of withstanding rapid cooling and resists premature heat
    checking. Tool Steel H13 has good machinability, good weldability, good
    ductility, and can be formed by conventional means.

    Due to H13
    tool steel excellent combination of high toughness and fatigue
    resistance, AISI H13 hot work tool steel is used more than any other
    tool steel in tooling applications.

    1. Common H13 Tool Steel Related Specifications

    Country USA German Japan
    Standard ASTM A681 DIN EN ISO 4957 JIS G4404
    Grades H13 1.2344/X40CrMoV5-1 SKD61

    2. H13 Tool Steel Chemical Composition

    ASTM A681 C Mn P S Si Cr V Mo
    H13 0.32 0.45 0.2 0.6 0.03 0.03 0.8 1.25 4.75 5.5 0.8 1.2 1.1 1.75
    DIN ISO 4957 C Mn P S Si Cr V Mo
    1.2344 /X40CrMoV5-1 0.35 0.42 0.25 0.5 0.03 0.02 0.8 1.2 4.8 5.5 0.85 1.15 1.1 1.5
    JIS G4404 C Mn P S Si Cr V Mo
    SKD61 0.35 0.42 0.25 0.5 0.03 0.02 0.8 1.2 4.8 5.5 0.8 1.15 1.0 1.5

    3. AISI H13 Steel Mechanical Properties

    Properties

    Metric Imperial
    Tensile strength, ultimate (@20°C/68°F, varies with heat treatment) 1200 – 1590 MPa 174000 – 231000 psi
    Tensile strength, yield (@20°C/68°F, varies with heat treatment) 1000 – 1380 MPa 145000 – 200000 psi
    Reduction of area (@20°C/68°F) 50.00% 50.00%
    Modulus of elasticity (@20°C/68°F) 215 GPa 31200 ksi
    Poisson’s ratio 0.27-0.30 0.27-0.30

    4. Forging of H13 Tool Steel
    Heating for forging must be done slowly and uniformly. Soak through at
    1900°-2000°F and reheat as often as necessary, stopping work when the
    temperature drops below 1650°F. After forging, cool slowly in lime,
    mica, dry ashes or furnace. H-13 should always be annealed after
    forging.

    5. Heat Treatment for H13 Tool Steels

    • Annealing

    Heat
    slowly to 1550°-1650°F, hold until entire mass is heated through, and
    cool slowly in the furnace (40F per hour) to about 1000°F, after which
    cooling rate may be increased. Suitable precautions must be taken to
    prevent excessive carburization or decarburization.

    • Stress Relieving

    When
    desirable to relieve the strains of machining, heat slowly to
    1050°-1250°F, allow to equalize, and then cool in still air (Strain
    Relieving). Â

    • Preheat Prior to Hardening

    Warm slightly before charging into the preheat furnace, which should be operating at 1400°-1500°F.

    • Hardening

    H13
    tool steel is a steel having very high hardenability and should be
    hardened by cooling in still air. The use of a salt bath or controlled
    atmosphere furnace is desirable to minimize decarburization, and if not
    available, pack hardening in spent pitch coke is suggested. The
    temperature employed is usually 1800°-1850°F, depending on size section.

    • Quenching

    Quench
    in still air or dry air blast. If complicated forms are to be hardened,
    an interrupted oil quench can be used. Quench part in oil and remove
    from bath when it just loses its color (1000°-1100°F). Finish cooling to
    below 150°-125°F in air, then temper immediately.

    • Tempering

    Tempering
    practice may vary with size and application, but is usually performed
    in the range of maximum secondary hardness or higher. Double tempering
    is recommended. The results below is H13 that was air quenched from
    1800°F and tempered for 4 hours at various temperatures. The results may
    be used as a guide, keeping in mind that parts of heavy section or mass
    may be several points lower in hardness.

    6. Application of AISI H13 Tool Steel

    • As Tools for Extrusion

    Part Aluminium, mag­nesium alloys, HRC Copper al­loys HRC Stainless steel HRC
    Dies, Backers, die-holders, liners, dummy blocks, stems 44-50 43-47 45-50
    41-50 40-48 40-48

    Austenitizing temperature

    1,870-1,885°F 1,900-1,920°F
    (1,020-1,030°C) (1,040-1,050°C)
    • As Plastic Molding Tool Steel

    Part Austenitizing temp. HRC
    Injection molds Compression/ transfer molds 1,870-1,885°F (1,020-1,030°C) 50-52
    Tempering 480°F (250°C)
    • Other Applications

    Applications Austenitizing temp HRC
    Severe cold punching, scrap shears 1,870-1,885°F 50-52
    (1,020-1,030°C)
    Tempering 480°F (250°C)
    Hot shearing 1,870-1,885°F
    (1,020-1,030°C) 50-52
    Tempering 480°F (250°C) or
    1,070-1,110°F 45-50
    (575-600°C)
    Shrink rings (e.g. for cemented carbide dies) 1,870-1,885°F 45-50
    (1,020-1,030°C)
    Tempering 1,070-1,110°F
    (575–600°C)
    Wear-resisting parts 1,870-1,885°F Core
    50-52
    Surface
    ~1000HV1
    (1,020-1,030°C)
    Tempering 1,070°F (575°C)
    nitrided

     

    If
    there are any queries about AISI H13 tool steel for hot working
    applications, please feel free to leave a comment below. And welcome
    enquiry of AISI H13 tool steel, we are professional and reliable
    supplier  for prime H13 tool steel materials.

  • Previous:
  • Next:



  • 555jewelry Stainless Steel 316L Tiny Ring แหวน รุ่น MNC-R687-A (Steel)
    ข้อมูล : http://p2b.us/76td5f

    คุณกำลังต้องการ 555jewelry Stainless Steel 316L Tiny Ring แหวน รุ่น MNC-R687-A (Steel) เพื่อช่วยแก้ไขปัญหา อยูใช่หรือไม่ ถ้าใช่คุณมาถูกที่แล้ว เรามีสินค้า ที่ท่านต้องการแนะนำ พร้อมมีแหล่งซื้อ สินค้าราคาถูก แนะนำให้ท่าน 555jewelry Stainless Steel 316L Tiny Ring แหวน รุ่น MNC-R687-A (Steel) ราคาถูกให้กับคุณ

    ซื้อของออนไลน์ ของแท้ ส่งฟรี เก็บเงินปลายทาง ราคาถูก 555jewelry Stainless Steel 316L Tiny Ring แหวน รุ่น MNC-R687-A (Steel) 555jewelry Stainless Steel 316L Ring แหวน รุ่น MNC-R687-A (Steel) คุณสมบัติ แหวนดีไซน์สวยงาม สามารถสวมใส่เข้าได้กับหลากหลายสไตล์การแต่งกาย วัสดุเป็น Stainless Steel เกรด316L เกรดเดียวกับเครื่องมือแพทย์ ดังนั้นจึงไม่ระคายเคืองต่อผิวหนัง มีความคงทน สีไม่หลุดลอก ไม่หมอง และไม่เป็นสนิม ตารางเทียบหาขนาดแหวน ข้อมูลจำเพาะของ 555jewelry Stainless Steel 316L Tiny Ring แหวน รุ่น MNC-R687-A (Steel) รายการสินค้าในกล่อง 555jewelry Stainless Steel 316L Ring แหวน รุ่น MNC-R687-A (Steel) คุณสมบัติทั่วไป ของแท้ ส่งฟรี เก็บเงินปลายทาง รับประกัน 55032OTAA3J1YPANTH-10040163 Main stone เพชรสวิส CZ Material โลหะ Metal สแตนเลส โมเดล 555Jewelry-MNCR687AJ09 Size (cm) 2 x 2 x 3 Weight (kg) 0.5 ของแท้ ของดี ส่งฟรี เก็บเงินปลายทาง…

    หมวดหมู่ 555jewelry-official-store
    ราคา 355 บาท ถูกที่สุด

    สั่งซื้อพร้อมส่วนลด เก็บเงินปลายทาง http://p2b.us/76td5f
    ———————————————————————————-
    คำค้นหา : 555jewelry, Stainless, Steel, 316L, Tiny, Ring, แหวน, รุ่น, MNCR687A, Steel, 555jewelry Stainless Steel 316L Tiny Ring แหวน รุ่น MNC-R687-A (Steel)

    555jewelry #Stainless #Steel #316L #Tiny #Ring #แหวน #รุ่น #MNCR687A #Steel #555jewelry Stainless Steel 316L Tiny Ring แหวน รุ่น MNC-R687-A (Steel)



    Knife sharpening and maintenance is an important skill in the kitchen. Learning how to sharpen a knife is a learned skill and learning how to maintain a knife is a learned skill as well. In this video we will look at the basics of honing your kitchen knives with a honing rod.

    The Knives I Use In My Kitchen

    http://goo.gl/xjNp7I

    The Gear I Use To Sharpen My Knives:
    DMT W6X: http://amzn.to/1anfp2A
    DMT W6F: http://amzn.to/15hhl74
    DMTW6CP: http://amzn.to/15hhyaq
    DMT W6E: http://amzn.to/1bSILDL

    DMT W8CXNB: http://amzn.to/19gxz4y
    DMT W8EFNB: http://amzn.to/129DEJP

    DMT W250CXNB: http://goo.gl/eS2Tu
    DMT250EFNB: http://amzn.to/19gydit

    SPECIAL PLATES:

    DMT D8EE: http://amzn.to/16FW1LO

    Spyderco 302UF: http://amzn.to/18Xq59O
    Spyderco 302U: http://amzn.to/18XqbhG
    Surgical Black Arkansas: http://amzn.to/129FPNu

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Key

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the House