Factory directly provided H13 Tool Steel | 1.2344 | X40CrMoV5-1 | SKD61 Hot Work Steel Supply to Georgia

Factory directly provided
 H13 Tool Steel | 1.2344 | X40CrMoV5-1 | SKD61 Hot Work Steel Supply to Georgia

Short Description:

H13 Tool Steel is chromium hot work tool steels which are widely used in hot and cold work tooling applications. H13 tool steel is classified as group H steels by the AISI classification system. This series of steels start from H1 to H19. AISI H-13 tool steel is characterized by: Good resistance to abrasion at both low and high temperatures High level of toughness and ductility Uniform and high level of machinability and polishability Good high-temperature strength and resistance to t...


  • Length: 3-5.8mm or Customization
  • Surface: black, peeled, or rough turned
  • Heat treatment: air-cooling, normalized, annealed, Q&T
  • Smelting process: EAF+LF+VD
  • Product Detail

    Product Tags

    It adheres to the tenet "Honest, industrious, enterprising, innovative" to develop new products constantly. It regards customers, success as its own success. Let us develop prosperous future hand in hand for Factory directly provided H13 Tool Steel | 1.2344 | X40CrMoV5-1 | SKD61 Hot Work Steel Supply to Georgia, Welcome to build the well and long standing business relationships with our company to create a glorious future together .customers' satisfaction is our eternal pursuit


    H13 Tool Steel is chromium hot work tool steels which are widely used in hot and cold work tooling applications. H13 tool steel is classified as group H steels by the AISI classification system. This series of steels start from H1 to H19.

    AISI H-13 tool steel is characterized by:

    • Good resistance to abrasion at both low and high temperatures

    • High level of toughness and ductility

    • Uniform and high level of machinability and polishability

    • Good high-temperature strength and resistance to thermal fatigue

    • Excellent through-hardening properties

    • Very limited distortion during hardening

    In
    steel H13, the molybdenum and vanadium act as strengthening agents. The
    chromium content assists die steel H-13 to resist softening when used
    at high temperatures. H-13 die steels offers an excellent combination of
    shock and abrasion resistance, and possesses good red hardness. It is
    capable of withstanding rapid cooling and resists premature heat
    checking. Tool Steel H13 has good machinability, good weldability, good
    ductility, and can be formed by conventional means.

    Due to H13
    tool steel excellent combination of high toughness and fatigue
    resistance, AISI H13 hot work tool steel is used more than any other
    tool steel in tooling applications.

    1. Common H13 Tool Steel Related Specifications

    Country USA German Japan
    Standard ASTM A681 DIN EN ISO 4957 JIS G4404
    Grades H13 1.2344/X40CrMoV5-1 SKD61

    2. H13 Tool Steel Chemical Composition

    ASTM A681 C Mn P S Si Cr V Mo
    H13 0.32 0.45 0.2 0.6 0.03 0.03 0.8 1.25 4.75 5.5 0.8 1.2 1.1 1.75
    DIN ISO 4957 C Mn P S Si Cr V Mo
    1.2344 /X40CrMoV5-1 0.35 0.42 0.25 0.5 0.03 0.02 0.8 1.2 4.8 5.5 0.85 1.15 1.1 1.5
    JIS G4404 C Mn P S Si Cr V Mo
    SKD61 0.35 0.42 0.25 0.5 0.03 0.02 0.8 1.2 4.8 5.5 0.8 1.15 1.0 1.5

    3. AISI H13 Steel Mechanical Properties

    Properties

    Metric Imperial
    Tensile strength, ultimate (@20°C/68°F, varies with heat treatment) 1200 – 1590 MPa 174000 – 231000 psi
    Tensile strength, yield (@20°C/68°F, varies with heat treatment) 1000 – 1380 MPa 145000 – 200000 psi
    Reduction of area (@20°C/68°F) 50.00% 50.00%
    Modulus of elasticity (@20°C/68°F) 215 GPa 31200 ksi
    Poisson’s ratio 0.27-0.30 0.27-0.30

    4. Forging of H13 Tool Steel
    Heating for forging must be done slowly and uniformly. Soak through at
    1900°-2000°F and reheat as often as necessary, stopping work when the
    temperature drops below 1650°F. After forging, cool slowly in lime,
    mica, dry ashes or furnace. H-13 should always be annealed after
    forging.

    5. Heat Treatment for H13 Tool Steels

    • Annealing

    Heat
    slowly to 1550°-1650°F, hold until entire mass is heated through, and
    cool slowly in the furnace (40F per hour) to about 1000°F, after which
    cooling rate may be increased. Suitable precautions must be taken to
    prevent excessive carburization or decarburization.

    • Stress Relieving

    When
    desirable to relieve the strains of machining, heat slowly to
    1050°-1250°F, allow to equalize, and then cool in still air (Strain
    Relieving). Â

    • Preheat Prior to Hardening

    Warm slightly before charging into the preheat furnace, which should be operating at 1400°-1500°F.

    • Hardening

    H13
    tool steel is a steel having very high hardenability and should be
    hardened by cooling in still air. The use of a salt bath or controlled
    atmosphere furnace is desirable to minimize decarburization, and if not
    available, pack hardening in spent pitch coke is suggested. The
    temperature employed is usually 1800°-1850°F, depending on size section.

    • Quenching

    Quench
    in still air or dry air blast. If complicated forms are to be hardened,
    an interrupted oil quench can be used. Quench part in oil and remove
    from bath when it just loses its color (1000°-1100°F). Finish cooling to
    below 150°-125°F in air, then temper immediately.

    • Tempering

    Tempering
    practice may vary with size and application, but is usually performed
    in the range of maximum secondary hardness or higher. Double tempering
    is recommended. The results below is H13 that was air quenched from
    1800°F and tempered for 4 hours at various temperatures. The results may
    be used as a guide, keeping in mind that parts of heavy section or mass
    may be several points lower in hardness.

    6. Application of AISI H13 Tool Steel

    • As Tools for Extrusion

    Part Aluminium, mag­nesium alloys, HRC Copper al­loys HRC Stainless steel HRC
    Dies, Backers, die-holders, liners, dummy blocks, stems 44-50 43-47 45-50
    41-50 40-48 40-48

    Austenitizing temperature

    1,870-1,885°F 1,900-1,920°F
    (1,020-1,030°C) (1,040-1,050°C)
    • As Plastic Molding Tool Steel

    Part Austenitizing temp. HRC
    Injection molds Compression/ transfer molds 1,870-1,885°F (1,020-1,030°C) 50-52
    Tempering 480°F (250°C)
    • Other Applications

    Applications Austenitizing temp HRC
    Severe cold punching, scrap shears 1,870-1,885°F 50-52
    (1,020-1,030°C)
    Tempering 480°F (250°C)
    Hot shearing 1,870-1,885°F
    (1,020-1,030°C) 50-52
    Tempering 480°F (250°C) or
    1,070-1,110°F 45-50
    (575-600°C)
    Shrink rings (e.g. for cemented carbide dies) 1,870-1,885°F 45-50
    (1,020-1,030°C)
    Tempering 1,070-1,110°F
    (575–600°C)
    Wear-resisting parts 1,870-1,885°F Core
    50-52
    Surface
    ~1000HV1
    (1,020-1,030°C)
    Tempering 1,070°F (575°C)
    nitrided

     

    If
    there are any queries about AISI H13 tool steel for hot working
    applications, please feel free to leave a comment below. And welcome
    enquiry of AISI H13 tool steel, we are professional and reliable
    supplier  for prime H13 tool steel materials.

  • Previous:
  • Next:



  • EPMAN 48MM Steel Open Exhtended Wheel Acorn Rim Lug Nuts Set
    รับส่วนลด คลิ๊ก : http://myriann.us/ckl02c

    EPMAN 48MM Steel Open Exhtended Wheel Acorn Rim Lug Nuts Set 12 x 1.25 Tuner 20 Pcs With One Key (Neochrome) EP-NUTV48-125-7C (Intl)นายท่านกำลังหาคำแนะนำสินค้า EPMAN 48MM Steel Open Exhtended Wheel Acorn Rim Lug Nuts Set 12 x 1.25 Tuner 20 Pcs With One Key (Neochrome) EP-NUTV48-125-7C (Intl) เพื่อช่วยแก้ไขปัญหา อยูใช่หรือไม่ ถ้าใช่คุณมาถูกที่แล้ว เรามีคำแนะนำดีๆ ที่คุณผู้หญิงต้องการ พร้อมให้คำแนะนำสถานที่ซื้อ สินค้า EPMAN 48MM Steel Open Exhtended Wheel Acorn Rim Lug Nuts Set 12 x 1.25 Tuner 20 Pcs With One Key (Neochrome) EP-NUTV48-125-7C (Intl) {ราคาดีที่สุด|ราคาถูกที่สุด|ราคาถูก|ราคาที่คุณสัมผัสได้ แนะนำให้คุณ EPMAN 48MM Steel Open Exhtended Wheel Acorn Rim Lug Nuts Set 12 x 1.25 Tuner 20 Pcs With One Key (Neochrome) EP-NUTV48-125-7C (Intl)
    สินค้าที่คุณซื้อได้ ด้วยความสบายใจ สินค้าคุณภาพ ราคาถูก ลดถึง80% จัดส่งถึงบ้านฟรี เก็บเงินปลายทางได้ EPMAN 48MM Steel Open Exhtended Wheel Acorn Rim Lug Nuts Set 12 x 1.25 Tuner 20 Pcs With One Key (Neochrome) EP-NUTV48-125-7C (Intl) Fuction:V48 Wheel Lug Nut Color:NeochromeBlueGoldenBlackPurpleGreenTitanium Fitment:Vehicle with Thread Pitch 12×1.25mm ONLY ( For Nissan For InfinitiFor SubaruFor Suzuki.It also fit other vehicles that uses a 12×1.25 Lug Nut. amp;nbsp;Only fit on Tuner wheels or Stock wheels with Acorn Conical or Tapered Seats amp;nbsp;Will NOT fit on wheels with Mag Seats or Ball Seats) Quantity:20pcs lug nuts 1 pcs keyamp;nbsp; Specifics:Thread Pitch M12x1.25 Width:22mm Key Diameter:24MM Quantity: 20pcs lug nuts 1 pcs keyamp;nbsp; Size: M12 x P1.25 Overall length: 48mm Material: Forged 50BV30 Steel Condition: 100% brand new in boxnever used or installed. Part No.SR48 V48 Style:For Aftermarket Wheel OnlyNot For Oem Wheels Racing Wheel Lug Nuts:Yes Wheel lug nuts:yes Auto lug nuts:yes Lug nuts:yes Wheel nuts:yes Made to fit many aftermarket wheels and OEM alloy wheels. Fit for most tuner wheels and some stock wheels with acorn conical or tapered seats. Please check the size of nuts on your wheels before buying.Easy Install. *Installation instructions not includedprofessional installation is highly recommended.*…

    บริการส่งฟรี สั่งซื้อพร้อมส่วนลด เก็บเงินปลายทาง http://myriann.us/ckl02c
    ———————————————————————————-
    ค้นหายอดนิยม : EPMAN, 48MM, Steel, Open, Exhtended, Wheel, Acorn, Rim, Lug, Nuts, Set, 12, x, 1.25, Tuner, 20, Pcs, With, One, Key, Neochrome, EPNUTV481257C, Intl, EPMAN 48MM Steel Open Exhtended Wheel Acorn Rim Lug Nuts Set 12 x 1.25 Tuner 20 Pcs With One Key (Neochrome) EP-NUTV48-125-7C (Intl)

    EPMAN #48MM #Steel #Open #Exhtended #Wheel #Acorn #Rim #Lug #Nuts #Set #12 #x #1.25 #Tuner #20 #Pcs #With #One #Key #Neochrome #EPNUTV481257C #Intl #EPMAN 48MM Steel Open Exhtended Wheel Acorn Rim Lug Nuts Set 12 x 1.25 Tuner 20 Pcs With One Key (Neochrome) EP-NUTV48-125-7C (Intl)



    Modeling of tensile test of a PEEK CF30 (30% Carbon Fiber reinforced PEEK) specimen using 3D automatic insertion of cohesive zones (cracks). Simulation performed using software MultiMech™ from MultiMechanics (http://www.multimechrd.com)

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Tree

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the Star