11 Years manufacturer BS EN 42CrMo4 | 1.7225 Alloy Engineering Steel Factory in Melbourne
BS EN 42crmo4 Alloy Steel is a common chromium-molybdenum steel that usually used after quenchedand tempered, with high intensity, high hardenability. BS EN 42CrMo4round steel has better performance than 34CrMo4 steel due to the carbonand chromium content is higher. 42CrMo4 alloy steel has higher strength and hardenability. The 42CrMo4 alloy material alsohas high fatigue strength and good low-temperature impact toughness. The temper brittleness is not obvious. Although 42CrMo4 steel is mo...
The customer satisfaction is our primary target. We uphold a consistent level of professionalism, quality, credibility and service for
11 Years manufacturer BS EN 42CrMo4 | 1.7225 Alloy Engineering Steel Factory in Melbourne, We warmly welcome customers from all over the world for any kind of cooperation with us to build a mutual benefit future. We are devoting ourselves wholeheartedly to offer customers the best service.
BS ENAlloy Steel
is a common chromium-molybdenum steel that usually used after quenched
and tempered, with high intensity, high hardenability. BS EN 42CrMo4
round steel has better performance than 34CrMo4 steel due to the carbon
and chromium content is higher.
has higher strength and hardenability. The 42CrMo4 alloy material also
has high fatigue strength and good low-temperature impact toughness. The
temper brittleness is not obvious.
Although 42CrMo4 steel is more expensive than 41Cr4 steel, it is more
preferable in terms of material properties. EN 42CrMo4 alloy
engineering steel materials have been widely used in automotive driving
elements. Otai Steel is able to supply you prime quality of 42CrMo4
alloy steel materials with wide range.
1.42CrMo4 Alloy Steel Supply Range
42CrMo4 Round bar Sizes: 80mm – 1200mm
Steel 42CrMo4 Flat and Plate: 10mm-1500mm thickness x 200-3000mm width
Other steel shape and sizes available according to your requirements.
Surface condition: Black, rough machined, peeled, turned or other requirements according to your requirements.
2.BS EN 42CrMo4 Alloy Steel Relevant Specifications and Equivalents
|BS EN 10250||Material No.||DIN||-3-1991||BS 970-1955||AS 1444||AFNOR|
3.42CrMo4 Alloy Steel Chemical Composition
|0.38-0.45||0.60-0.90||0.40 max||0.035 max||0.035 max||0.90-1.20||0.15-0.30|
4. DIN 42CrMo4 Alloy Steel Mechanical Properties
|Size Ø mm||Yield stress
|Ultimate tensile Stress,
KV, Joule, min.
|<40||750||1000-1200||11||295-355||35 at 20ºC|
|40-95||650||900-1100||12||265-325||35 at 20ºC|
|>95||550||800-950||13||235-295||35 at 20ºC|
5. Heat Treatment of 42CrMo4 Steels
Annealing of 42CrMo4 Steels
Heat steel 42CrMo4 forged steel slowly and thoroughly to 800-850°C;
Cool slowly in the furnace to the temperature 480°;
Complete annealing the steel in the air.
Quenched and Tempered (Q+T)
Heat 42CrMo4 steel slowly to 880°C;
Soak at this temperature then quench in oil;
Temper as soon as 42CrMo4 steel reach room temperature (20°C);
Heat uniformly to the suitable temperature of 560°C;
Withdraw the 42CrMo4 material from the furnace and cool in the air.
6. Forging of 42CrMo4 Alloy Steel
Preheat 42CrMo4 engineering steel uniformly and slowly;
Increase the forging temperature up to 1150-1200°C.
Always keep the forging temperature above at least 850°C
steel 42CrMo4 has only limited weldability. Preheating to 200-300°C is
strongly recommended; the upper limit should not be exceeded because of
risk for deterioration of the chrome layer.
Alloy steel 42CrMo4
can be friction welded. However, precautions are necessary so as to
limit the formation of undesirable microstructures in the welded zone.
8.Application of 42CrMo4 Alloy Steels
42CrMo4 alloy steel is widely used for engineering steel purpose, such
as: making various kinds of machinery, automobile, mining spare part,
the gearwheel of the engine, the driving gear of supercharger, the
connecting rob, the pinchock under the high pressure, parts for power
train applications, cold formed fastener components, shafts, gears,
drill collars for the oil exploration, etc.
Erosion is very common in manufacturing, during which material failure occurs and contact interfaces keep changing. Here by Abaqus, I simulation a case that a steel rod erodes a steel plate at 2000 m/s. Thanks for your watch.