Rapid Delivery for C45 Round Bar | AISI 1045 | DIN 1.1191 | JIS S45C Factory in Tanzania

Rapid Delivery for
 C45 Round Bar | AISI 1045 | DIN 1.1191 | JIS S45C Factory in Tanzania

Short Description:

Steel C45 Round Bar is an unalloyed medium carbon steel, which is also a general carbon engineering steel. C45 is a medium strength steel with good machinability and excellent tensile properties. C45 round steel is generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 – 700 Mpa and Brinell hardness range 170 – 210 in either condition. It does not however respond satisfactorily to nitriding due to a lack of suita...


  • Length: 3-5.8mm or Customization
  • Surface: black, peeled, or rough turned
  • Heat treatment: air-cooling, normalized, annealed, Q&T
  • Smelting process: EAF+LF+VD
  • Product Detail

    Product Tags

    Our products are widely recognized and trusted by users and can meet continuously developing economic and social needs for Rapid Delivery for C45 Round Bar | AISI 1045 | DIN 1.1191 | JIS S45C Factory in Tanzania, We sincerely welcome overseas customers to consult for the long-term cooperation and the mutual development.


    Steel C45 Round Bar is
    an unalloyed medium carbon steel, which is also a general carbon
    engineering steel. C45 is a medium strength steel with good
    machinability and excellent tensile properties. C45 round steel is
    generally supplied in the black hot rolled or occasionally in the
    normalised condition, with a typical tensile strength range 570 – 700
    Mpa and Brinell hardness range 170 – 210 in either condition. It does
    not however respond satisfactorily to nitriding due to a lack of
    suitable alloying elements.

    C45 round bar steel is equivalent to EN8 or 080M40.
    Steel C45 bar or plate is suitable for the manufacture of parts such as
    gears, bolts, general-purpose axles and shafts, keys and studs.

    1. Supply Range of Steel C45 Round Bar

    • C45 Steel Round Bar: diameter 8mm – 3000mm

    • C45 Steel Plate: thickness 10mm – 1500mm  x width 200mm – 3000mm

    • C45 Steel Flat Bar: 200mm – 1000mm

    • Square C45 Steel: 20mm-800mm

    • Hexagon Steel.

    Surface Finish: Black, Rough Machined, Turned or as per given requirements.

    2. Common C45 Steel Specifications

    Country USA British Japan Australia
    Standard ASTM A29 EN 10083-2 JIS G4051 AS 1442
    Grades 1045 C45/1.1191 S45C 1045

    3. C45 Round Bar Steel Chemical Composition Properties

    Standard Grade C Mn P S Si Ni Cr
    ASTM A29 1045 0.43-0.50 0.60-0.90 0.04 0.050  -  -  -
    EN 10083-2 C45/1.1191 0.42-0.50 0.50-0.90 0.03 0.035 0.04 0.4 0.4
    JIS G4051 S45C 0.42-0.48 0.60-0.90 0.03 0.035 0.15-0.35  -  -

    4. Mechanical Properties of C45 Round Bar Steel Material

    • Mechanical Properties in Quenched+Tempered Condition

    Diameter d (mm) Thickness t (mm) 0.2 % proof stress (N/mm2) Tensile strength (N/mm2) Elongation A5 (%) Reduction Z (%)
    <16 <8 min. 490 700-850 min. 14 min. 35
    <17-40 <8<=20 min. 430 650-800 min. 16 min. 40
    <41-100 <20<=60 min. 370 630-780 min. 17 min. 45
    Diameter d (mm) Thickness t (mm) 0.2 % proof stress (N/mm2) Tensile strength (N/mm2) Elongation A5(%)
    <16 <16 min. 390 min. 620 min. 14
    <17-100 <16<=100 min. 305 min. 305 min. 16
    <101-250 <100<250 min. 275 min. 560 min. 16

    5. Forging of Carbon Steel C45 Round Bar

    Hot forming temperature: 850-1200oC.

    Pre
    heat to 750 oC – 800 oC, then continue heating to 1100 oC – 1200 oC
    maximum, hold until temperature is uniform throughout the section and
    commence forging immediately. Forging is not workable below 850 oC.
    Finished forgings could be air cooled.

    We are strong on forged steel C45 round bar. Welcome enquiry of C45 steel materials.

    6. DIN C45 Round Bar Steel Grade Heat Treatment

    Forging or hot rolling: 1100 – 850°C
    Normalising:  840 – 880°C/air
    Soft annealing:  680 – 710°C/furnace
    Hardening:  820 – 860°C/water, oil
    Tempering:  550 – 660°C/air

    7. Hardening of DIN C45 Steel Hardening

    Harden from a temperature of 820-860oC followed by water or oil quenching.

    Heat
    to 820 oC – 850 oC hold until temperature is uniform throughout the
    section, soak for 10 – 15 minutes per 25mm of section, and quench in
    water or brine. Or,

    Heat to 830 oC – 860 oC soak as above and quench in oil.Temper immediately while still hand warm.

    Surface hardness for C45 special steel round bar after flame or induction hardning:

    • Steel Name       Steel number          Surface Harndess

    • C45                        1.1191                        min. 55 HRC

    8. Application of DIN Carbon Steel C45 Round Bar

    DIN
    C45 round bar steel material and steel plate C45, flats are widely used
    in all industry for uses which require more strength and wear
    resistance than the low carbon mild steel.

    Quenched and
    subsequently tempered steel for C45 steel grade round bar, steel plate,
    flat and square is used for axles, bolts, forged connecting rods,
    crankshafts, torsion bars, light gears, guide rods, screws, forgings,
    wheel tyres, shafts, sickles, axes, knives, wood working drills,
    hammers, etc.

    Welcome customers to inquiry DIN C45 round bar,
    CK45/1.1191 steel plate, flat steel for C45 steel price. We are
    professional supplier and exporter for more than 20 years. We offer you
    worldwide solution for C45 round bar steel.

  • Previous:
  • Next:



  • Description http://www.advancedglobalmaterials.com, or Call us at 631-286-8570 for a quote. We supply all AMS Specs, Alloy Steel,Stainless Steel,Aluminum, Titanium and Nickel



    A Tutorial Video Media Expose all the necessary requirements to detach the Lower Intake Plenum Manifold from the Nissan Engine VG33E 60 degree V6 Engine(Block). We Show you How-To dis-assemble the Engine Wiring Harness. The Fuel Lines and its Fuel Injector Rail. Removal of the VG33E and VG33ER(supercharge) V6 Engine Lower Plenum Intake Manifold from its Engine Block. Know-How to take apart the Intake Lower Plenum Manifold Removal(COMPLETE). SAFETY FIRST. Also SEE: https://www.youtube.com/watch?v=vjL24ojaYtM for the other Item essential for removal. We show the best way to reuse the Factory OEM Stainless Steel Shim Gasket. Learn some of the technique to avoid breaking parts before applying your self to these things.
    Here is a related video media which will offer more information pertaining to the video be view , NOW!.

    The Video Application May remain the same has for the listed models and year Below.

    1996–2000 Nissan Pathfinder
    1996–2004 Nissan Pathfinder In Australian Models
    1997–2000 Infiniti QX4
    1999–2004 Nissan Frontier
    2000–2004 Nissan Xterra
    1997–2002 Nissan Elgrand
    1999–2002 Nissan Quest/Mercury Villager
    200?–200? Nissan Paladin

    Some Application and Procedure remain the same for the Nissan VG33ER(Supercharge) and VG33ET(Turbo-Charge).

    During the process of removing the lower engine plinum manifold you will most likely run into problem with the Heater Core hose and its plastic connection. Here is how to replace the heater exchange core https://www.youtube.com/watch?v=7AZBh5jwqIg should you run into rotten plastic heater core tube.

    Thank You for your Viewer-Ship Please STAY-TUNE.

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Cup

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the House