High Quality Industrial Factory AISI304| SUS304| EN1.4948 Supply to Burundi

High Quality Industrial Factory
 AISI304| SUS304| EN1.4948 Supply to Burundi

Short Description:

Chemical Composition of Stainless Steel 304 Table 1. Chemical composition for 304 stainless steel alloys % 304 304L 304H C 0.0 – 0.07 0.0 – 0.03 0.04 – 0.08 Mn 0.0 – 2.0 0.0 – 2.00 0.0 – 2.0 Si 0.0 – 1.00 0.0 – 1.00 0.0 – 1.0 P 0.0 – 0.05 0.0 – 0.05 0.0 – 0.04 S 0.0 – 0.03 0.0 – 0.02 0.0 – 0.02 Cr 17.50 – 19.50 17.50 – 19.50 ...


  • Length: 3-5.8mm or Customization
  • Surface: black, peeled, or rough turned
  • Heat treatment: air-cooling, normalized, annealed, Q&T
  • Smelting process: EAF+LF+VD
  • Product Detail

    Product Tags

    "Quality first, Honesty as base, Sincere service and mutual profit" is our idea, in order to develop continuously and pursue the excellence for High Quality Industrial Factory AISI304| SUS304| EN1.4948 Supply to Burundi, Create Values,Serving Customer!" is the aim we pursue. We sincerely hope that all customers will establish long term and mutually beneficial cooperation with us.If you wish to get more details about our company, Please contact with us now.


    Chemical Composition of Stainless Steel 304

    Table 1. Chemical composition for 304 stainless steel alloys

    %

    304

    304L

    304H

    C

    0.0 – 0.07

    0.0 – 0.03

    0.04 – 0.08

    Mn

    0.0 – 2.0

    0.0 – 2.00

    0.0 – 2.0

    Si

    0.0 – 1.00

    0.0 – 1.00

    0.0 – 1.0

    P

    0.0 – 0.05

    0.0 – 0.05

    0.0 – 0.04

    S

    0.0 – 0.03

    0.0 – 0.02

    0.0 – 0.02

    Cr

    17.50 – 19.50

    17.50 – 19.50

    17.00 – 19.00

    Ni

    8.00 – 10.50

    8.00 – 10.50

    8.00 – 11.00

    Fe

    Balance

    Balance

    Balance

    N

    0.0-0.11

    0.0-0.11

    0.0 – 0.10

    Properties of Stainless Steel 304

    Mechanical Properties of Stainless Steel 304

    Table 2a. Mechanical properties for 304 stainless steel alloys – sheet up to 8 mm thick

    Grade

    304

    304L

    304H

    Tensile Strength (MPa)

    540 – 750

    520 – 700

    -

    Proof Stress (MPa)

    230 Min

    220 Min

    -

    Elongation A50 mm

    45 Min %

    45 Min %

    -


    Table 2b. Mechanical properties for 304 stainless steel alloys – plate from 8 – 75 mm thick

    Grade

    304

    304L

    304H

    Tensile Strength (MPa)

    520 – 720

    500 – 700

    -

    Proof Stress (MPa)

    210 Min

    200 Min

    -

    Elongation A5

    45 Min %

    45 Min %

    -


    Table 2c. Mechanical properties for 304 stainless steel alloys – bar and section up to 160 mm diameter / thickness

    Grade

    304

    304L

    304H

    Tensile Strength (MPa)

    500 – 700

    500 – 700

    500 – 700

    Proof Stress (MPa)

    190

    175 Min

    185 Min

    Elongation A50 mm

    45 Min %

    45 Min %

    40 Min %

    Hardness Brinell

    215 Max HB

    215 Max HB

    -

    Physical Properties of Stainless Steel 304

    Table 3. Physical properties for 304 stainless steel alloys

    Property

    Value

    Density

    8.00 g/cm3

    Melting Point

    1450 °C

    Modulus of Elasticity

    193 GPa

    Electrical Resistivity

    0.072 x 10-6 Ω.m

    Thermal Conductivity

    16.2 W/m.K

    Thermal Expansion

    17.2 x 10-6 /K

    Alloy Designations

    Stainless steel 304 also corresponds to the following standard designations and specifications:

    Euronorm

    UNS

    BS

    En

    Grade

    1.4301

    S30400

    304S15

    304S16

    304S31

    58E

    304

    1.4306

    S30403

    304S11

    -

    304L

    1.4307

    -

    304S11

    -

    304L

    1.4311

    -

    304S11

    -

    304L

    1.4948

    S30409

    304S51

    -

    304H

    Corrosion Resistance of Stainless Steel 304

    Stainless steel 304
    has excellent corrosion resistance in a wide variety of environments
    and when in contact with different corrosive media. Pitting and crevice
    corrosion can occur in environments containing chlorides. Stress
    corrosion cracking can occur at temperatures over 60°C.

    Heat Resistance of Stainless Steel 304

    Stainless steel 304 has
    good resistance to oxidation in intermittent service up to 870°C and in
    continuous service to 925°C. However, continuous use at 425-860°C is
    not recommended if corrosion resistance in water is required. In this
    instance 304L is recommended due to its resistance to carbide
    precipitation.

    Where high strength is required at temperatures above 500°C and up to
    800°C, grade 304H is recommended. This material will retain aqueous
    corrosion resistance.

    Fabrication of Stainless Steel 304

    Fabrication of all stainless steels should
    be done only with tools dedicated to stainless steel materials. Tooling
    and work surfaces must be thoroughly cleaned before use. These
    precautions are necessary to avoid cross contamination of stainless steel by easily corroded metals that may discolour the surface of the fabricated product.

    Cold Working of Stainless Steel 304

    Stainless steel 304 readily
    work hardens. Fabrication methods involving cold working may require an
    intermediate annealing stage to alleviate work hardening and avoid
    tearing or cracking. At the completion of fabrication a full annealing
    operation should be employed to reduce internal stresses and optimise
    corrosion resistance.

    Hot Working of Stainless Steel 304

    Fabrication methods, like forging, that involve hot working should
    occur after uniform heating to 1149-1260°C. The fabricated components
    should then be rapidly cooled to ensure maximum corrosion resistance.

    Heat Treatment of Stainless Steel 304

    Stainless steel 304 cannot be hardened by heat treatment.

    Solution treatment or annealing can be done by rapid cooling after heating to 1010-1120°C.

    Machinability

    Stainless steel 304 has good machinability. Machining can be enhanced by using the following rules:

    • Cutting edges must be kept sharp. Dull edges cause excess work hardening.

    • Cuts should be light but deep enough to prevent work hardening by riding on the surface of the material.

    • Chip breakers should be employed to assist in ensuring swarf remains clear of the work

    • Low thermal conductivity of austenitic alloys results in heat
      concentrating at the cutting edges. This means coolants and lubricants
      are necessary and must be used in large quantities.

    Welding of Stainless Steel 304

    Fusion welding performance for Stainless steel 304 is excellent both with and without fillers. Recommended filler rods and electrodes for stainless steel 304 is grade 308 stainless steel.
    For 304L the recommended filler is 308L. Heavy welded sections may
    require post-weld annealing. This step is not required for 304L. Grade
    321 may be used if post-weld heat treatment is not possible.

    Applications of Stainless Steel 304

    Stainless steel 304 is typically used in:

    • Sinks and splashbacks

    • Saucepans

    • Cutlery and flatware

    • Architectural panelling

    • Sanitaryware and troughs

    • Tubing

    • Brewery, dairy, food and pharmaceutical production equipment

    • Springs, nuts, bolts and screws

  • Previous:
  • Next:



  • Help Make These Videos Possible By Supporting my Patreon Page – And Enjoy Exclusive Rewards!

    https://www.patreon.com/ChuckE2009

    Interested in MIG welding lessons? Here’s a YouTube playlist that will take you through initial machine setup, as well as horizontal, vertical, and even overhead welding…

    Interested in A Career In Welding? Click Here:

    http://www.georgiatradeschool.com/

    ChuckE2009 Facebook Page:

    https://www.facebook.com/pages/ChuckE2009/282164941819994

    You can learn MIG for free:

    http://www.youtube.com/playlist?list=SP_P7k0CDx5cWywuZRYRd3HDZuvy7mTH0k

    Having issues with your mig welds? We’ll take a look at a number of common problems (been there, done that) in this How Not To Weld video on the GMAW (Gas Metal Arc Welding) Process.

    Here’s what we talk about, in order:

    Traveling Too Fast
    Traveling Too Slow

    Too Much WFS (Wire Feed Speed)
    Too Little WFS (Wire Feed Speed)

    Too Much Stick-Out
    Not Enough Stick-Out

    Wrong Polarity

    No Shielding Gas… Or Not Enough Shielding Gas

    Welding “Too Hot”
    Welding “Too Cold”

    The “Swan-Neck” gun that fits my Hobart 187, and other Miller/Hobart machines:

    http://www.usaweld.com/15-Flexible-Swan-Neck-Gun-fits-Miller-Welders-p/m2015-fsbe.htm

    It honestly isnt a bad upgrade, for $137…

    General Selection of “Swan-Neck” guns:

    http://www.usaweld.com/Welding-Accessories-s/44.htm

    General Selection of HTP Mig Wire:

    http://www.usaweld.com/Steel-Wire-s/53.htm

    Two rolls, shipped (The same ones I got) for $35:

    http://www.usaweld.com/035-ER70S-6-Steel-Wire-10-lbs-Spool-p/er70s6-030-35-2pkmixed3.htm

    ChuckE2009 Official Facebook Page:

    http://www.facebook.com/pages/ChuckE2009/282164941819994

    Enjoy the video? Then be sure to check out my website for more:

    http://www.weldingwithstretch.com/



    Houghton have a long standing history with the AMRC and NAMRC. Craig Hamp tells MTD all about it including how they developed HOCUT 795N with the help of the AMRC for the machining of heat resistant alloys and stainless steels. Also included in the video is Craig telling Joe Reynolds about the fantastic support he gets from Houghton’s fluid care program.

    MTDCNC are proud to offer a platform that educates engineers throughout the World. Our main audience is the UK market and you’ll see from this video that we focus on learning and talking to UK based engineers. We do travel to Europe and review products on request of our clients.

    See Videos on MTDCNC here http://www.mtdcnc.com/tv/

    It’s not just videos that MTDCNC offers to our users, we promote used machine tools for sale, new machine tools for sale, ex demo machines and also related equipment, such as cutting tools, including end mills, drills, countersinking tools, shell mills, radius tools, boring tools, reamers and much more for both milling and turning. Beyond the cutting tools we also offer the accessory solutions, these include the Workholding, vices, 4th axis units, collet chucks, 3 jaw chucks, bar feeds and toolholders. Toolholders is an interesting one as this could be one of many differing toolholders such at BT40 tooling, BT30, HSK 63 and then for turning VDI 30/VDI 40 toolholders.

    Find new and used machine tools for sale here http://www.mtdcnc.com/products/machine-tools
    Find cutting tools for sale here http://www.mtdcnc.com/products/cutting-tools
    Find workholding, vices and more here http://www.mtdcnc.com/products/machine-accessories
    Find automation for machine tools here http://www.mtdcnc.com/products/automation
    Find CAD CAM software here http://www.mtdcnc.com/products/cad-cam

    Our website also has a great news feed, we deliver news to the UK market every hour relating to manufacturing, machine tools, cnc equipment and events.

    For the latest news click here http://www.mtdcnc.com/news/
    For machine tool and tooling user stories http://www.mtdcnc.com/stories/

    Check out our event videos, they really are unique. In all our youtube channel and our website are great for engineers and machinists.

    You can also follow us on twitter here https://twitter.com/MTDonline
    And on Facebook here: https://www.facebook.com/MTDCNC
    Our LinkedIn discussion group: https://www.linkedin.com/groups/4154874

    AND DON’T FORGET TO SUBSCRIBE TO THIS YOUTUBE CHANNEL TO GET MORE OF OUR GREAT ENGINEERING VIDEOS!

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Plane

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the Key