Factory provide nice price L6 Tool Steel | 1.2714 | 55NiCrMoV7 | SKT4 | BH224/5 Factory from Denmark

Factory provide nice price
 L6 Tool Steel | 1.2714 | 55NiCrMoV7 | SKT4 | BH224/5 Factory from Denmark

Short Description:

In ASTM A681 standard, L6 steel grade is in L-type for special purpose tool steels. AISI L6 tool steel is in the general class of alloy, oil-hardening tool steel that is characterized by good toughness. ASTM L6 tool steel is suitable for use as tools, dies, and machine parts, which require a good combination of hardness and toughness. Due to its lower carbon content and relatively high nickel content, L6 tool steel has slightly better shock-resistance than more highly alloyed types and shoul...


  • Length: 3-5.8mm or Customization
  • Surface: black, peeled, or rough turned
  • Heat treatment: air-cooling, normalized, annealed, Q&T
  • Smelting process: EAF+LF+VD
  • Product Detail

    Product Tags

    We depend on sturdy technical force and continually create sophisticated technologies to meet the demand of Factory provide nice price L6 Tool Steel | 1.2714 | 55NiCrMoV7 | SKT4 | BH224/5 Factory from Denmark, We sincerely welcome all guests to set up business relationships with us on the basis of mutual benefits. Please contact us now. You will get our professional reply within 8 hours.


    In ASTM A681 standard, L6 steel grade is in L-type for special purpose tool steels. AISI L6 tool steel
    is in the general class of alloy, oil-hardening tool steel that is
    characterized by good toughness. ASTM L6 tool steel is suitable for use
    as tools, dies, and machine parts, which require a good combination of
    hardness and toughness.

    Due to its lower carbon content and
    relatively high nickel content, L6 tool steel has slightly better
    shock-resistance than more highly alloyed types and should be used where
    some wear-resistance can be sacrificed for increased toughness.

    1. Relevant Steel Specification of L6 Tool Steel

    Country USA German Japan British
    Standard ASTM A681 DIN EN ISO 4957 JIS G4404 BS 4659
    Grades L6/T61206 1.2714/55NiCrMoV7 SKT4 BH224/5

    2. AISI L6 Steel Chemical Composition and Steel Equivalents

    ASTM A681 C Mn P S Si Cr V Mo Ni
    L6/T61206 0.65 0.75 0.25 0.80 0.03 0.03 0.10 0.50 0.60 1.20 . . . . . . . . . 0.50 1.25 2.00
    DIN ISO 4957 C Mn P S Si Cr V Mo Ni
    1.2714/55NiCrMoV7 0.50 0.60 0.60 0.90 0.03 0.02 0.10 0.40 0.80 1.20 0.05 0.15 0.35 0.55 1.50 1.80
    JIS G4404 C Mn P S Si Cr V Mo Ni
    SKT4 0.50 0.60 0.60 0.90 0.03 0.02 0.10 0.40 0.80 1.20 0.05 0.15 0.35 0.55 1.50 1.80
    BS 4659 C Mn P S Si Cr V Mo Ni
    BH224/5 0.49 0.57 0.70 1.00 0.03 0.025 . . . 0.35 0.70 1.10 . . . . . . 0.25 0.40 1.25 1.80

    3. ASTM L6 Tool Steel Mechanical Properties

    Steel L6 Physical Properties

    • Modulus of elasticity [103 x N/mm2]: 215

    • Density [g/cm3]: 7.84

    • Thermal conductivity [W/m.K]: 36.0

    • Electric resistivity [Ohm mm2/m]: 0.30

    • Specific heat capacity[J/g.K]: 0.46

    Mechanical Properties of L6 Steels

    Properties Metric Imperial
    Poisson’s ratio 0.27- 0.30 0.27- 0.30
    Elastic modulus 190-210 GPa 27557-30457 ksi

    4. Forging of L6 Tool Steel

    Forge at 1079°C (1975 F) down to 871°C (1600 F). Do not forge below 843°C (1550 F).

    5. AISI L6 Tool Steel Heat Treatment

    Hardening

    Preheating:
    Heat steel L6 at a rate not exceeding 204°C (400°F) per hour (222°C per
    hour) to 621-677°C (1150-1250°F) and equalize. Soak for 30 minutes for
    the first inch (25.4 mm) of thickness, plus 15 minutes for each
    additional inch (25.4 mm).

    Quenching

    Quench L6 tool steel in oil to 66-51°C (150-125°F).

    Tempering

    Temper
    L6 steels immediately after quenching. Hold at temperature for 1 hour
    per inch (25.4 mm) of thickness when tempering at 204°C (400°F), 4 hours
    minimum, then air cool to ambient temperature.
    However, where increased toughness is desired, at a sacrifice of some hardness, higher tempering temperatures are often used.

    AISI L6 steel does not become brittle, as many other die steels do, when tempered in the range of 232°C to 426°C (450 to 800°F).

    To
    minimize the possibility of cracking, the steel should be tempered
    immediately after hardening and should be heated slowly to the desired
    tempering temperature.

    Annealing

    Annealing of steel L6 must be performed after hot working and before re-hardening.

    Heat
    to 760°C (1400°F) and hold one hour per inch of maximum thickness. Then
    cool slowly with the furnace at a rate not exceeding 28°C per hour(50°F
    per hour) to 538°C (1000°F). Continue cooling to ambient temperature in
    the furnace or in air.

    For improved machinability, hold at 760°C
    (1400°F) for 1 hour per inch (25.4mm) of maximum thickness; 2 hours
    minimum. Then cool slowly with the furnace cool from 677°C (1250°F) to
    760°C (1400°F), hold for 8 hours, then air cool to ambient temperature.

    Because of its air-hardening ability, steel L6 should not be normalized.

    6. Machinability of Steel L6

    Machinability
    of tool steel L6 is very good. It rates 90% of the machinability of the
    W-group water hardening low alloy steels rated 100% as a baseline.

    7. Applications of ASTM A681 L6 Tool Steel

    AISI
    L6 cold working tool steel is for general purpose tools and dies where
    greater toughness is required, but with some sacrifice of
    abrasion-resistance.

    Typically used below applications:

    • spindles,

    • forming rolls,

    • punches,

    • blanking and forming dies,

    • trimmer dies,

    • clutch parts,

    • pawls,

    • bearings,

    • chucks parts,

    • rollers,

    • knuckle pins,

    • clutch pins,

    • shear blades

  • Previous:
  • Next:



  • “FD Grip” The No.1 earthquake-resistant rebar coupler in Japan, the optimum seismic place,
    for over 30 years.
    TEL:+62-21-6471-2565 http://www.fujibolt.com/index.html



    Houghton have a long standing history with the AMRC and NAMRC. Craig Hamp tells MTD all about it including how they developed HOCUT 795N with the help of the AMRC for the machining of heat resistant alloys and stainless steels. Also included in the video is Craig telling Joe Reynolds about the fantastic support he gets from Houghton’s fluid care program.

    MTDCNC are proud to offer a platform that educates engineers throughout the World. Our main audience is the UK market and you’ll see from this video that we focus on learning and talking to UK based engineers. We do travel to Europe and review products on request of our clients.

    See Videos on MTDCNC here http://www.mtdcnc.com/tv/

    It’s not just videos that MTDCNC offers to our users, we promote used machine tools for sale, new machine tools for sale, ex demo machines and also related equipment, such as cutting tools, including end mills, drills, countersinking tools, shell mills, radius tools, boring tools, reamers and much more for both milling and turning. Beyond the cutting tools we also offer the accessory solutions, these include the Workholding, vices, 4th axis units, collet chucks, 3 jaw chucks, bar feeds and toolholders. Toolholders is an interesting one as this could be one of many differing toolholders such at BT40 tooling, BT30, HSK 63 and then for turning VDI 30/VDI 40 toolholders.

    Find new and used machine tools for sale here http://www.mtdcnc.com/products/machine-tools
    Find cutting tools for sale here http://www.mtdcnc.com/products/cutting-tools
    Find workholding, vices and more here http://www.mtdcnc.com/products/machine-accessories
    Find automation for machine tools here http://www.mtdcnc.com/products/automation
    Find CAD CAM software here http://www.mtdcnc.com/products/cad-cam

    Our website also has a great news feed, we deliver news to the UK market every hour relating to manufacturing, machine tools, cnc equipment and events.

    For the latest news click here http://www.mtdcnc.com/news/
    For machine tool and tooling user stories http://www.mtdcnc.com/stories/

    Check out our event videos, they really are unique. In all our youtube channel and our website are great for engineers and machinists.

    You can also follow us on twitter here https://twitter.com/MTDonline
    And on Facebook here: https://www.facebook.com/MTDCNC
    Our LinkedIn discussion group: https://www.linkedin.com/groups/4154874

    AND DON’T FORGET TO SUBSCRIBE TO THIS YOUTUBE CHANNEL TO GET MORE OF OUR GREAT ENGINEERING VIDEOS!

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Flag

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the Heart