29 Years Factory H13 Tool Steel | 1.2344 | X40CrMoV5-1 | SKD61 Hot Work Steel Wholesale to Bangkok
H13 Tool Steel is chromium hot work tool steels which are widely used in hot and cold work tooling applications. H13 tool steel is classified as group H steels by the AISI classification system. This series of steels start from H1 to H19. AISI H-13 tool steel is characterized by: Good resistance to abrasion at both low and high temperatures High level of toughness and ductility Uniform and high level of machinability and polishability Good high-temperature strength and resistance to t...
We believe that long term partnership is a result of high quality, value added service, rich experience and personal contact for 29 Years Factory H13 Tool Steel | 1.2344 | X40CrMoV5-1 | SKD61 Hot Work Steel Wholesale to Bangkok, We are sincere and open. We look forward to your visit and establishing trustworthy and long-term standing relationship.
is chromium hot work tool steels which are widely used in hot and cold work tooling applications. is classified as group H steels by the AISI classification system. This series of steels start from H1 to H19.
AISI H-13 tool steel is characterized by:
Good resistance to abrasion at both low and high temperatures
High level of toughness and ductility
Uniform and high level of machinability and polishability
Good high-temperature strength and resistance to thermal fatigue
Excellent through-hardening properties
Very limited distortion during hardening
steel H13, the molybdenum and vanadium act as strengthening agents. The
chromium content assists die steel H-13 to resist softening when used
at high temperatures. H-13 die steels offers an excellent combination of
shock and abrasion resistance, and possesses good red hardness. It is
capable of withstanding rapid cooling and resists premature heat
checking. Tool Steel H13 has good machinability, good weldability, good
ductility, and can be formed by conventional means.
Due to H13
tool steel excellent combination of high toughness and fatigue
resistance, AISI H13 hot work tool steel is used more than any other
tool steel in tooling applications.
1. Common H13 Tool Steel Related Specifications
2. H13 Tool Steel Chemical Composition
|DIN ISO 4957||C||Mn||P||S||Si||Cr||V||Mo|
3. AISI H13 Steel Mechanical Properties
|Tensile strength, ultimate (@20°C/68°F, varies with heat treatment)||1200 – 1590 MPa||174000 – 231000 psi|
|Tensile strength, yield (@20°C/68°F, varies with heat treatment)||1000 – 1380 MPa||145000 – 200000 psi|
|Reduction of area (@20°C/68°F)||50.00%||50.00%|
|Modulus of elasticity (@20°C/68°F)||215 GPa||31200 ksi|
4. Forging of H13 Tool Steel
Heating for forging must be done slowly and uniformly. Soak through at
1900°-2000°F and reheat as often as necessary, stopping work when the
temperature drops below 1650°F. After forging, cool slowly in lime,
mica, dry ashes or furnace. H-13 should always be annealed after
5. Heat Treatment for H13 Tool Steels
slowly to 1550°-1650°F, hold until entire mass is heated through, and
cool slowly in the furnace (40F per hour) to about 1000°F, after which
cooling rate may be increased. Suitable precautions must be taken to
prevent excessive carburization or decarburization.
desirable to relieve the strains of machining, heat slowly to
1050°-1250°F, allow to equalize, and then cool in still air (Strain
Preheat Prior to Hardening
Warm slightly before charging into the preheat furnace, which should be operating at 1400°-1500°F.
tool steel is a steel having very high hardenability and should be
hardened by cooling in still air. The use of a salt bath or controlled
atmosphere furnace is desirable to minimize decarburization, and if not
available, pack hardening in spent pitch coke is suggested. The
temperature employed is usually 1800°-1850°F, depending on size section.
in still air or dry air blast. If complicated forms are to be hardened,
an interrupted oil quench can be used. Quench part in oil and remove
from bath when it just loses its color (1000°-1100°F). Finish cooling to
below 150°-125°F in air, then temper immediately.
practice may vary with size and application, but is usually performed
in the range of maximum secondary hardness or higher. Double tempering
is recommended. The results below is H13 that was air quenched from
1800°F and tempered for 4 hours at various temperatures. The results may
be used as a guide, keeping in mind that parts of heavy section or mass
may be several points lower in hardness.
6. Application of AISI H13 Tool Steel
As Tools for Extrusion
|Part||Aluminium, magnesium alloys, HRC||Copper alloys HRC||Stainless steel HRC|
|Dies, Backers, die-holders, liners, dummy blocks, stems||44-50||43-47||45-50|
As Plastic Molding Tool Steel
|Injection molds Compression/ transfer molds||1,870-1,885°F (1,020-1,030°C)||50-52|
|Tempering 480°F (250°C)|
|Severe cold punching, scrap shears||1,870-1,885°F||50-52|
|Tempering 480°F (250°C)|
|Tempering 480°F (250°C) or|
|Shrink rings (e.g. for cemented carbide dies)||1,870-1,885°F||45-50|
|Tempering 1,070°F (575°C)|
there are any queries about AISI H13 tool steel for hot working
applications, please feel free to leave a comment below. And welcome
enquiry of AISI H13 tool steel, we are professional and reliable
supplier for prime H13 tool steel materials.
surface hardening 4140 steel alloy
Forever has a long history of manufacturing induction heating equipment for a variety of applications throughout forging and heat treatment industry. We pride ourselves on supplying the most reliable, durable and efficient induction heating equipment available to the industry today. The offered induction heating equipment can be used for bar & billet Heating, Forging, Rolling Hot Forming, Extrusion, Heat Treatment including surface hardening,Tempering and Annealing, Tube and wire heating,Continuous heating, Stress relieving and so on.
Contact person: Hailee
Billet induction heater:
Bar,billet induction heating:
Induction forging heating equipment :
Autoleader 75MM MITRE CLAMPS 4 CORNER CLAMP Picture Holder W
ข้อมูลทั้งหมด : http://buy.diarymom.com/UwQ4Y
Autoleader 75MM MITRE CLAMPS 4 CORNER CLAMP Picture Holder Woodwork Right Angle (Intl)
นายท่านกำลังค้นหาสินค้า Autoleader 75MM MITRE CLAMPS 4 CORNER CLAMP Picture Holder Woodwork Right Angle (Intl) เพื่อช่วยอำนวยความสะดวก อยูใช่หรือไม่ ถ้าใช่คุณมาถูกที่แล้ว เรามีสิ่งของ ที่คุณผู้ชายต้องการ เรามีร้านค้าขาย สินค้า Autoleader 75MM MITRE CLAMPS 4 CORNER CLAMP Picture Holder Woodwork Right Angle (Intl) ราคาที่สัมผัสได้ แนะนำให้คุณผู้ชาย Autoleader 75MM MITRE CLAMPS 4 CORNER CLAMP Picture Holder Woodwork Right Angle (Intl)
ซื้อของออนไลน์ ของแท้ ของดี มีคุณภาพ จัดส่งเร็ว เก็บเงินปลายทาง Autoleader 75MM MITRE CLAMPS 4 CORNER CLAMP Picture Holder Woodwork Right Angle (Intl) Features: 90 ° right angle clamp. Holds joints at a 90 degree angle. Can also be used for 45 degree sawing. Great for picture framing and wood working. Aluminium alloy construction with steel screws. Independently adjustable jaws. Pre drilling mounting holes to allow fixing to work surfaces. Maximum clamping range 7.5CM generally 4 right-angle clamp all together to use. Material: Aluminum Type: 4 -inch Color: Red 205 บาท shop-home-and-living …
ค้นหายอดนิยม : Autoleader, 75MM, MITRE, CLAMPS, 4, CORNER, CLAMP, Picture, Holder, Woodwork, Right, Angle, Intl, Autoleader 75MM MITRE CLAMPS 4 CORNER CLAMP Picture Holder Woodwork Right Angle (Intl)
Autoleader #75MM #MITRE #CLAMPS #4 #CORNER #CLAMP #Picture #Holder #Woodwork #Right #Angle #Intl #Autoleader 75MM MITRE CLAMPS 4 CORNER CLAMP Picture Holder Woodwork Right Angle (Intl)