28 Years Factory AISI304| SUS304| EN1.4948 Kenya

28 Years Factory
 AISI304| SUS304| EN1.4948 Kenya

Short Description:

Chemical Composition of Stainless Steel 304 Table 1. Chemical composition for 304 stainless steel alloys % 304 304L 304H C 0.0 – 0.07 0.0 – 0.03 0.04 – 0.08 Mn 0.0 – 2.0 0.0 – 2.00 0.0 – 2.0 Si 0.0 – 1.00 0.0 – 1.00 0.0 – 1.0 P 0.0 – 0.05 0.0 – 0.05 0.0 – 0.04 S 0.0 – 0.03 0.0 – 0.02 0.0 – 0.02 Cr 17.50 – 19.50 17.50 – 19.50 ...


  • Length: 3-5.8mm or Customization
  • Surface: black, peeled, or rough turned
  • Heat treatment: air-cooling, normalized, annealed, Q&T
  • Smelting process: EAF+LF+VD
  • Product Detail

    Product Tags

    We are proud of the high customer satisfaction and wide acceptance due to our persistent pursuit of high quality both on product and service for 28 Years Factory AISI304| SUS304| EN1.4948 Kenya, As we are moving forward, we keep an eye on our ever-expanding product range and make improvement to our services.


    Chemical Composition of Stainless Steel 304

    Table 1. Chemical composition for 304 stainless steel alloys

    %

    304

    304L

    304H

    C

    0.0 – 0.07

    0.0 – 0.03

    0.04 – 0.08

    Mn

    0.0 – 2.0

    0.0 – 2.00

    0.0 – 2.0

    Si

    0.0 – 1.00

    0.0 – 1.00

    0.0 – 1.0

    P

    0.0 – 0.05

    0.0 – 0.05

    0.0 – 0.04

    S

    0.0 – 0.03

    0.0 – 0.02

    0.0 – 0.02

    Cr

    17.50 – 19.50

    17.50 – 19.50

    17.00 – 19.00

    Ni

    8.00 – 10.50

    8.00 – 10.50

    8.00 – 11.00

    Fe

    Balance

    Balance

    Balance

    N

    0.0-0.11

    0.0-0.11

    0.0 – 0.10

    Properties of Stainless Steel 304

    Mechanical Properties of Stainless Steel 304

    Table 2a. Mechanical properties for 304 stainless steel alloys – sheet up to 8 mm thick

    Grade

    304

    304L

    304H

    Tensile Strength (MPa)

    540 – 750

    520 – 700

    -

    Proof Stress (MPa)

    230 Min

    220 Min

    -

    Elongation A50 mm

    45 Min %

    45 Min %

    -


    Table 2b. Mechanical properties for 304 stainless steel alloys – plate from 8 – 75 mm thick

    Grade

    304

    304L

    304H

    Tensile Strength (MPa)

    520 – 720

    500 – 700

    -

    Proof Stress (MPa)

    210 Min

    200 Min

    -

    Elongation A5

    45 Min %

    45 Min %

    -


    Table 2c. Mechanical properties for 304 stainless steel alloys – bar and section up to 160 mm diameter / thickness

    Grade

    304

    304L

    304H

    Tensile Strength (MPa)

    500 – 700

    500 – 700

    500 – 700

    Proof Stress (MPa)

    190

    175 Min

    185 Min

    Elongation A50 mm

    45 Min %

    45 Min %

    40 Min %

    Hardness Brinell

    215 Max HB

    215 Max HB

    -

    Physical Properties of Stainless Steel 304

    Table 3. Physical properties for 304 stainless steel alloys

    Property

    Value

    Density

    8.00 g/cm3

    Melting Point

    1450 °C

    Modulus of Elasticity

    193 GPa

    Electrical Resistivity

    0.072 x 10-6 Ω.m

    Thermal Conductivity

    16.2 W/m.K

    Thermal Expansion

    17.2 x 10-6 /K

    Alloy Designations

    Stainless steel 304 also corresponds to the following standard designations and specifications:

    Euronorm

    UNS

    BS

    En

    Grade

    1.4301

    S30400

    304S15

    304S16

    304S31

    58E

    304

    1.4306

    S30403

    304S11

    -

    304L

    1.4307

    -

    304S11

    -

    304L

    1.4311

    -

    304S11

    -

    304L

    1.4948

    S30409

    304S51

    -

    304H

    Corrosion Resistance of Stainless Steel 304

    Stainless steel 304
    has excellent corrosion resistance in a wide variety of environments
    and when in contact with different corrosive media. Pitting and crevice
    corrosion can occur in environments containing chlorides. Stress
    corrosion cracking can occur at temperatures over 60°C.

    Heat Resistance of Stainless Steel 304

    Stainless steel 304 has
    good resistance to oxidation in intermittent service up to 870°C and in
    continuous service to 925°C. However, continuous use at 425-860°C is
    not recommended if corrosion resistance in water is required. In this
    instance 304L is recommended due to its resistance to carbide
    precipitation.

    Where high strength is required at temperatures above 500°C and up to
    800°C, grade 304H is recommended. This material will retain aqueous
    corrosion resistance.

    Fabrication of Stainless Steel 304

    Fabrication of all stainless steels should
    be done only with tools dedicated to stainless steel materials. Tooling
    and work surfaces must be thoroughly cleaned before use. These
    precautions are necessary to avoid cross contamination of stainless steel by easily corroded metals that may discolour the surface of the fabricated product.

    Cold Working of Stainless Steel 304

    Stainless steel 304 readily
    work hardens. Fabrication methods involving cold working may require an
    intermediate annealing stage to alleviate work hardening and avoid
    tearing or cracking. At the completion of fabrication a full annealing
    operation should be employed to reduce internal stresses and optimise
    corrosion resistance.

    Hot Working of Stainless Steel 304

    Fabrication methods, like forging, that involve hot working should
    occur after uniform heating to 1149-1260°C. The fabricated components
    should then be rapidly cooled to ensure maximum corrosion resistance.

    Heat Treatment of Stainless Steel 304

    Stainless steel 304 cannot be hardened by heat treatment.

    Solution treatment or annealing can be done by rapid cooling after heating to 1010-1120°C.

    Machinability

    Stainless steel 304 has good machinability. Machining can be enhanced by using the following rules:

    • Cutting edges must be kept sharp. Dull edges cause excess work hardening.

    • Cuts should be light but deep enough to prevent work hardening by riding on the surface of the material.

    • Chip breakers should be employed to assist in ensuring swarf remains clear of the work

    • Low thermal conductivity of austenitic alloys results in heat
      concentrating at the cutting edges. This means coolants and lubricants
      are necessary and must be used in large quantities.

    Welding of Stainless Steel 304

    Fusion welding performance for Stainless steel 304 is excellent both with and without fillers. Recommended filler rods and electrodes for stainless steel 304 is grade 308 stainless steel.
    For 304L the recommended filler is 308L. Heavy welded sections may
    require post-weld annealing. This step is not required for 304L. Grade
    321 may be used if post-weld heat treatment is not possible.

    Applications of Stainless Steel 304

    Stainless steel 304 is typically used in:

    • Sinks and splashbacks

    • Saucepans

    • Cutlery and flatware

    • Architectural panelling

    • Sanitaryware and troughs

    • Tubing

    • Brewery, dairy, food and pharmaceutical production equipment

    • Springs, nuts, bolts and screws

  • Previous:
  • Next:



  • Carbon steel pipe suppliers? Call Federal Steely Supply Inc., at 800-325-1584 or visit http://www.fedsteel.com/ where our motto is “Global reach, exceptional service”. We will be the alloy, stainless steel, and carbon steel pipe suppliers that you need. We have over 4,000 individual parts from thirty different product lines that can be packed and shipped either around the corner or around the globe. As of right now we are the carbon steel pipe suppliers for several different industries and markets in over 20 countries. Emergency weekend and after hour carbon steel pipe supplier services are also available any time you need.

    Do you need carbon steel pipe suppliers? Look no further than Federal Steel Supply where we can meet any and all of your carbon steel pipe needs. As the premier carbon steel pipe suppliers, our carbon steel pipes and tubes specifically range from ½” nominal through 60″ OD and varying sizes of thickness, and we have a number of specifications & grades to choose from:

    • A-106 Grade B/C
    • SA-106 Grade B/C
    • A-333, Grade 1/6
    • API 5LB & X-Grades through X-80
    • A-53 Grade B
    • SA-53 Grade B
    • A-519
    • A-513 Type 5 (DOM)
    • Rolled and Welded A-671 & A672

    Keep in mind we also follow American Society for Testing and Materials guidelines, ensuring we are the safest and best carbon steel pipe suppliers you could use. For all carbon steel pipe supplies, speak to the best carbon steel pipe supplier, Federal Steel Supply.

    A carbon steel pipe supplier is more commonly requested than any other metal supplier because of the affordability when compared to other types of metals. Federal Steel Supply is your number one carbon steel pipe suppliers, including any seamless or welded carbon steel pipe products you may need.

    Not only can we be your carbon steel pipe supplier, but we can also be your supplier for alloy and stainless steel. Apart from being the premier carbon steel pipe suppliers we also specialize in “chrome moly”, which is used extensively in power plants worldwide. Our stainless steel like have unsurpassed corrosion resistance, high strength, durability, and machinability.

    As carbon steel pipe suppliers, we also provide complete lines of fittings and flanges to complement our seamless and welded pipe products. They’re available in alloy and stainless steel as well. Size ranges from ¼” through 48″ OD for both fittings and flanges, and each has a number of specifications & grades.

    If you need carbon steel pipe suppliers, use Federal Steel Supply. We accept most major credit cards and will ship to you anywhere in the world. If you have any questions about our services and products, call us at (800) 325-1584 or visit us at http://www.fedsteel.com.

    On our website you can also chat online with us directly and request a quote. Look to Federal Steel Supply as your carbon steel pipe supplier. Global reach, exceptional service.

    Our Contact Information

    Phone : 800-325-1584
    Website : http://www.fedsteel.com/
    Email : info@fedsteel.com
    Address : 747 Goddard Avenue, Chesterfield MO 63005

    Get Social with Federal Steel Supply!
    Youtube : http://www.youtube.com/watch?v=0fv6m-XeVOM&feature=youtu.be

    Video Marketing by OMG National: http://www.omgnational.com



    Melting down 1 gram bars of Silver, Copper, Nickel and Brass with hydrogen and oxygen. Brass is already an alloy of copper and zinc, and did not melt down easy as a I learned from my Brass, Lead and Gunpowder video. I then combine the three workable metals Silver, copper and nickel to create…….Silvcopickel

    SUBSCRIBE: http://full.sc/1bnslc9
    FACEBOOK: http://full.sc/1dT2aaM

    RHNB Vs. Watermelon – http://full.sc/1bns60F
    RHNB Vs. Jello – http://full.s/1bns0WF RHNB Vs. Elmers Glue – http://full.sc/1dT1TEM
    RHNB Full Playlist – http://full.sc/1dT1WjP -Want to send an object / material / substance to be RHNB’d or HHO’d? SEND HERE with a full credit of your donation! PO Box 21 96 Seymour St. Tonawanda NY 14150 USA

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Cup

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the Heart