27 Years Factory AISI 1053 Carbon Steel (UNS G10530) Wholesale to Bolivia

27 Years Factory
 AISI 1053 Carbon Steel (UNS G10530) Wholesale to Bolivia

Short Description:

Chemical Composition The chemical composition of AISI 1053 carbon steel is outlined in the following table. Element Content (%) Iron, Fe 98.36-98.82 Manganese, Mn 0.7-1.0 Carbon, C 0.48-0.55 Sulfur, S 0.05 Phosphorous, P 0.04 Physical Properties The physical properties of AISI 1053 carbon steel are tabulated below. Properties Metric Imperial Density 7.7-8.03 g/cm3 0.278-0.290 l...


  • Length: 3-5.8mm or Customization
  • Surface: black, peeled, or rough turned
  • Heat treatment: air-cooling, normalized, annealed, Q&T
  • Smelting process: EAF+LF+VD
  • Product Detail

    Product Tags

    Our company insists all along the quality policy of "product quality is base of enterprise survival; customer satisfaction is the staring point and ending of an enterprise; persistent improvement is eternal pursuit of staff" and the consistent purpose of "reputation first, customer first" for 27 Years Factory AISI 1053 Carbon Steel (UNS G10530) Wholesale to Bolivia, We will wholeheartedly welcome all clients in the industry both at home and abroad to cooperate hand in hand, and create a bright future together.


    Chemical Composition

    The chemical composition of AISI 1053 carbon steel is outlined in the following table.

    Element Content (%)
    Iron, Fe 98.36-98.82
    Manganese, Mn 0.7-1.0
    Carbon, C 0.48-0.55
    Sulfur, S 0.05
    Phosphorous, P 0.04

    Physical Properties

    The physical properties of AISI 1053 carbon steel are tabulated below.

    Properties Metric Imperial
    Density 7.7-8.03 g/cm3 0.278-0.290 lb/in3

    Mechanical Properties

    The following table shows mechanical properties of AISI 1053 carbon steel.

    Properties Metric Imperial
    Elastic modulus 190-210 GPa 29700-30458 ksi
    Poisson’s ratio 0.27-0.30 0.27-0.30

  • Previous:
  • Next:



  • http://MuggyWeld.com

    Super Alloy 1 can easily solder galvanized steel plates together.

    Super Alloy 1 has a very low melting point which prevents the galvanized coating from burning through. Super Alloy 1 has a working temperature of only 350 degrees F.

    Simply add the flux first, when the flux turns brown when heated by any propane,MAPP gas,butane, or oxyacetylene torch, then add the rod. Be careful not to heat the flux or rod directly.

    For more videos and information, or to order, visit http://MuggyWeld.com

    Please read all instructions prior to use at: http://muggyweld.com/packets/superalloy1postsale.pdf
    Pre-cleaning is necessary with Super Alloy 1

    _______________________

    Please visit http://www.aws.org/technical/facts/ prior to using Muggy Weld products, and adhere to all AWS welding safety guidelines. Further product safety information is available at http://muggyweld.com/safety-guidelines.

    Muggy Weld LLC shall not be liable for any loss, injury, claim, liability, or damage of any kind resulting in any way from (a) your use of this Site, (b) any services or products obtained from this Site, (c) any errors in or omissions from this Site, (d) the unavailability or interruption of this Site or any features thereof, (e) any content contained on this Site.

    MSDS sheets available with purchase from MuggyWeld.com, upon request.



    I have tried several methods of cutting up wheels for melting and the method show I have found works best.
    Special thin aluminium cutting discs in an angle grinder wear out too quickly. The Evolution saw runs at a slower speed that a woodworking saw and the Evolution blade cuts the metal OK but the fine teeth clog easily and can break off when cleaned out. The blade shown has fewer teeth so there is no room for metal to clog them.

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Truck

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the Flag