2016 New Style AISI304| SUS304| EN1.4948 Factory for Doha

2016 New Style
 AISI304| SUS304| EN1.4948 Factory for Doha

Short Description:

Chemical Composition of Stainless Steel 304 Table 1. Chemical composition for 304 stainless steel alloys % 304 304L 304H C 0.0 – 0.07 0.0 – 0.03 0.04 – 0.08 Mn 0.0 – 2.0 0.0 – 2.00 0.0 – 2.0 Si 0.0 – 1.00 0.0 – 1.00 0.0 – 1.0 P 0.0 – 0.05 0.0 – 0.05 0.0 – 0.04 S 0.0 – 0.03 0.0 – 0.02 0.0 – 0.02 Cr 17.50 – 19.50 17.50 – 19.50 ...


  • Length: 3-5.8mm or Customization
  • Surface: black, peeled, or rough turned
  • Heat treatment: air-cooling, normalized, annealed, Q&T
  • Smelting process: EAF+LF+VD
  • Product Detail

    Product Tags

    Our company since its inception, always regards product quality as enterprise life, continuously improve production technology, improve product quality and continuously strengthen enterprise total quality management, in strict accordance with the national standard ISO 9001:2000 for 2016 New Style AISI304| SUS304| EN1.4948 Factory for Doha, Welcome to build the well and long standing business relationships with our company to create a glorious future together .customers' satisfaction is our eternal pursuit


    Chemical Composition of Stainless Steel 304

    Table 1. Chemical composition for 304 stainless steel alloys

    %

    304

    304L

    304H

    C

    0.0 – 0.07

    0.0 – 0.03

    0.04 – 0.08

    Mn

    0.0 – 2.0

    0.0 – 2.00

    0.0 – 2.0

    Si

    0.0 – 1.00

    0.0 – 1.00

    0.0 – 1.0

    P

    0.0 – 0.05

    0.0 – 0.05

    0.0 – 0.04

    S

    0.0 – 0.03

    0.0 – 0.02

    0.0 – 0.02

    Cr

    17.50 – 19.50

    17.50 – 19.50

    17.00 – 19.00

    Ni

    8.00 – 10.50

    8.00 – 10.50

    8.00 – 11.00

    Fe

    Balance

    Balance

    Balance

    N

    0.0-0.11

    0.0-0.11

    0.0 – 0.10

    Properties of Stainless Steel 304

    Mechanical Properties of Stainless Steel 304

    Table 2a. Mechanical properties for 304 stainless steel alloys – sheet up to 8 mm thick

    Grade

    304

    304L

    304H

    Tensile Strength (MPa)

    540 – 750

    520 – 700

    -

    Proof Stress (MPa)

    230 Min

    220 Min

    -

    Elongation A50 mm

    45 Min %

    45 Min %

    -


    Table 2b. Mechanical properties for 304 stainless steel alloys – plate from 8 – 75 mm thick

    Grade

    304

    304L

    304H

    Tensile Strength (MPa)

    520 – 720

    500 – 700

    -

    Proof Stress (MPa)

    210 Min

    200 Min

    -

    Elongation A5

    45 Min %

    45 Min %

    -


    Table 2c. Mechanical properties for 304 stainless steel alloys – bar and section up to 160 mm diameter / thickness

    Grade

    304

    304L

    304H

    Tensile Strength (MPa)

    500 – 700

    500 – 700

    500 – 700

    Proof Stress (MPa)

    190

    175 Min

    185 Min

    Elongation A50 mm

    45 Min %

    45 Min %

    40 Min %

    Hardness Brinell

    215 Max HB

    215 Max HB

    -

    Physical Properties of Stainless Steel 304

    Table 3. Physical properties for 304 stainless steel alloys

    Property

    Value

    Density

    8.00 g/cm3

    Melting Point

    1450 °C

    Modulus of Elasticity

    193 GPa

    Electrical Resistivity

    0.072 x 10-6 Ω.m

    Thermal Conductivity

    16.2 W/m.K

    Thermal Expansion

    17.2 x 10-6 /K

    Alloy Designations

    Stainless steel 304 also corresponds to the following standard designations and specifications:

    Euronorm

    UNS

    BS

    En

    Grade

    1.4301

    S30400

    304S15

    304S16

    304S31

    58E

    304

    1.4306

    S30403

    304S11

    -

    304L

    1.4307

    -

    304S11

    -

    304L

    1.4311

    -

    304S11

    -

    304L

    1.4948

    S30409

    304S51

    -

    304H

    Corrosion Resistance of Stainless Steel 304

    Stainless steel 304
    has excellent corrosion resistance in a wide variety of environments
    and when in contact with different corrosive media. Pitting and crevice
    corrosion can occur in environments containing chlorides. Stress
    corrosion cracking can occur at temperatures over 60°C.

    Heat Resistance of Stainless Steel 304

    Stainless steel 304 has
    good resistance to oxidation in intermittent service up to 870°C and in
    continuous service to 925°C. However, continuous use at 425-860°C is
    not recommended if corrosion resistance in water is required. In this
    instance 304L is recommended due to its resistance to carbide
    precipitation.

    Where high strength is required at temperatures above 500°C and up to
    800°C, grade 304H is recommended. This material will retain aqueous
    corrosion resistance.

    Fabrication of Stainless Steel 304

    Fabrication of all stainless steels should
    be done only with tools dedicated to stainless steel materials. Tooling
    and work surfaces must be thoroughly cleaned before use. These
    precautions are necessary to avoid cross contamination of stainless steel by easily corroded metals that may discolour the surface of the fabricated product.

    Cold Working of Stainless Steel 304

    Stainless steel 304 readily
    work hardens. Fabrication methods involving cold working may require an
    intermediate annealing stage to alleviate work hardening and avoid
    tearing or cracking. At the completion of fabrication a full annealing
    operation should be employed to reduce internal stresses and optimise
    corrosion resistance.

    Hot Working of Stainless Steel 304

    Fabrication methods, like forging, that involve hot working should
    occur after uniform heating to 1149-1260°C. The fabricated components
    should then be rapidly cooled to ensure maximum corrosion resistance.

    Heat Treatment of Stainless Steel 304

    Stainless steel 304 cannot be hardened by heat treatment.

    Solution treatment or annealing can be done by rapid cooling after heating to 1010-1120°C.

    Machinability

    Stainless steel 304 has good machinability. Machining can be enhanced by using the following rules:

    • Cutting edges must be kept sharp. Dull edges cause excess work hardening.

    • Cuts should be light but deep enough to prevent work hardening by riding on the surface of the material.

    • Chip breakers should be employed to assist in ensuring swarf remains clear of the work

    • Low thermal conductivity of austenitic alloys results in heat
      concentrating at the cutting edges. This means coolants and lubricants
      are necessary and must be used in large quantities.

    Welding of Stainless Steel 304

    Fusion welding performance for Stainless steel 304 is excellent both with and without fillers. Recommended filler rods and electrodes for stainless steel 304 is grade 308 stainless steel.
    For 304L the recommended filler is 308L. Heavy welded sections may
    require post-weld annealing. This step is not required for 304L. Grade
    321 may be used if post-weld heat treatment is not possible.

    Applications of Stainless Steel 304

    Stainless steel 304 is typically used in:

    • Sinks and splashbacks

    • Saucepans

    • Cutlery and flatware

    • Architectural panelling

    • Sanitaryware and troughs

    • Tubing

    • Brewery, dairy, food and pharmaceutical production equipment

    • Springs, nuts, bolts and screws

  • Previous:
  • Next:



  • Turning insert brochures are available for download at http://www.mitsubishicarbide.com/mmus/en/product/catalog/turning.html

    Mitsubishi offers special J-Series breakers and micro-grain grades for turning difficult to cut materials. Mitsubishi breakers for heat resistant alloys include the FJ (light cutting), MJ (medium cutting) and GJ (medium to semi-heavy cutting). The offering is completed with the addition of the dual rake MS (medium cutting) breaker and round RCMX insert also for medium cutting. FJ and MJ series insert are available in G Class tolerances for applications that require a strong sharp cutting edge. For Titanium and non-ferrous materials, the polished FJ-P/MJ-P version is available.

    The FJ’s sharp cutting geometry is available in standard .002, .004, .008 and .016″ tool nose radius. While the MS and MJ tool nose radius starts at .016 and the GJ at .031″ and up. Our heat resistant alloy breakers are available in a wide range of micro-grain grades specifically design for this market segment. Our micro-grain grades are available non-coated or topped off with PVD/CVD coatings and edge preparations to suit to the insert application range.

    Available uncoated grades are: RT9005, RT9010, TF15 and Hti10.
    Our MIRACLE Coating (Al, Ti)N PVD grades are: VP05RT, VP10RT and VP15TF.
    CVD coated US905 is design to provide unequalled wear resistance in stable high speed applications. The close microstructure of US905 CVD coatings limits insert flank and face wear at high speeds when compared to other products. US905 has the highest hardness cemented carbide substrate suitable for CVD Coating.

    To see all Mitsubishi Cutting Tool product channels on YouTube, follow link:

    http://www.youtube.com/user/mitsubishicarbide/videos?view=1

    Or

    Visit one of our product specific channels below:
    The Cutting Edge: http://www.youtube.com/playlist?list=PL1CEA67C978F3029D&feature=view_all
    Turning & Boring Channel: http://www.youtube.com/playlist?list=PL0D406ECCFFF53995&feature=view_all
    Milling Channel: http://www.youtube.com/playlist?list=PL648BF1B051AE20F0&feature=view_all
    Drilling Channel: http://www.youtube.com/playlist?list=PL6960075BD195101A&feature=view_all
    Grooving Channel: http://www.youtube.com/playlist?list=PL3AD4CC3127719A38&feature=view_all
    Swiss Tooling Channel: http://www.youtube.com/playlist?list=PL0FBAAF2F0230343C&feature=view_all
    CBN Channel: http://www.youtube.com/playlist?list=PLBB88F97F9A2B5376&feature=view_all
    Solid Carbide End Mill Channel: http://www.youtube.com/playlist?list=PL7A1549BEF477EDDB&feature=view_all

    Mitsubishi Materials USA – Cutting Tools, Social Media Sites:
    Facebook: http://www.facebook.com/MitsubishiMaterials.US.CuttingTools
    Twitter: http://twitter.com/#!/MMUSCuttingTool
    YouTube: http://www.youtube.com/user/mitsubishicarbide

    Additional Resources:
    Experience Mitsubishi Carbide’s Patented Online Catalog with downloadable CAD files http://www.mitsubishicarbide.net/mmus/en/catalogue/index.html
    More Mitsubishi Cutting Tool Videos can be found at http://www.mitsubishicarbide.com/mmus/en/product/video/index.html

    Questions please contact:
    Technical Support at 1-800-486-2341
    Or
    Email MarketingServices@mmus.com
    Secure technical inquires can be submitted to Mitsubishi Materials at https://www.mitsubishicarbide.com/mailform/mmus/en/literature/form.html

    Thank you for taking the time to view this video and please visit Mitsubishi Materials USA at http://www.mmus.com



    “FD Grip” The No.1 earthquake-resistant rebar coupler in Japan, the highest seismic country,
    for over 30 years.
    TEL:+62-21-6471-2565 http://www.fujibolt.com/index.html

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Heart

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the Heart