12 Years manufacturer AISI304| SUS304| EN1.4948 Brazil

12 Years manufacturer
 AISI304| SUS304| EN1.4948 Brazil

Short Description:

Chemical Composition of Stainless Steel 304 Table 1. Chemical composition for 304 stainless steel alloys % 304 304L 304H C 0.0 – 0.07 0.0 – 0.03 0.04 – 0.08 Mn 0.0 – 2.0 0.0 – 2.00 0.0 – 2.0 Si 0.0 – 1.00 0.0 – 1.00 0.0 – 1.0 P 0.0 – 0.05 0.0 – 0.05 0.0 – 0.04 S 0.0 – 0.03 0.0 – 0.02 0.0 – 0.02 Cr 17.50 – 19.50 17.50 – 19.50 ...


  • Length: 3-5.8mm or Customization
  • Surface: black, peeled, or rough turned
  • Heat treatment: air-cooling, normalized, annealed, Q&T
  • Smelting process: EAF+LF+VD
  • Product Detail

    Product Tags

    Innovation, quality and reliability are the core values of our company. These principles today more than ever form the basis of our success as an internationally active mid-size company for 12 Years manufacturer AISI304| SUS304| EN1.4948 Brazil, "Passion, Honesty, Sound service, Keen cooperation and Development" are our goals. We are here expecting friends all over the world!


    Chemical Composition of Stainless Steel 304

    Table 1. Chemical composition for 304 stainless steel alloys

    %

    304

    304L

    304H

    C

    0.0 – 0.07

    0.0 – 0.03

    0.04 – 0.08

    Mn

    0.0 – 2.0

    0.0 – 2.00

    0.0 – 2.0

    Si

    0.0 – 1.00

    0.0 – 1.00

    0.0 – 1.0

    P

    0.0 – 0.05

    0.0 – 0.05

    0.0 – 0.04

    S

    0.0 – 0.03

    0.0 – 0.02

    0.0 – 0.02

    Cr

    17.50 – 19.50

    17.50 – 19.50

    17.00 – 19.00

    Ni

    8.00 – 10.50

    8.00 – 10.50

    8.00 – 11.00

    Fe

    Balance

    Balance

    Balance

    N

    0.0-0.11

    0.0-0.11

    0.0 – 0.10

    Properties of Stainless Steel 304

    Mechanical Properties of Stainless Steel 304

    Table 2a. Mechanical properties for 304 stainless steel alloys – sheet up to 8 mm thick

    Grade

    304

    304L

    304H

    Tensile Strength (MPa)

    540 – 750

    520 – 700

    -

    Proof Stress (MPa)

    230 Min

    220 Min

    -

    Elongation A50 mm

    45 Min %

    45 Min %

    -


    Table 2b. Mechanical properties for 304 stainless steel alloys – plate from 8 – 75 mm thick

    Grade

    304

    304L

    304H

    Tensile Strength (MPa)

    520 – 720

    500 – 700

    -

    Proof Stress (MPa)

    210 Min

    200 Min

    -

    Elongation A5

    45 Min %

    45 Min %

    -


    Table 2c. Mechanical properties for 304 stainless steel alloys – bar and section up to 160 mm diameter / thickness

    Grade

    304

    304L

    304H

    Tensile Strength (MPa)

    500 – 700

    500 – 700

    500 – 700

    Proof Stress (MPa)

    190

    175 Min

    185 Min

    Elongation A50 mm

    45 Min %

    45 Min %

    40 Min %

    Hardness Brinell

    215 Max HB

    215 Max HB

    -

    Physical Properties of Stainless Steel 304

    Table 3. Physical properties for 304 stainless steel alloys

    Property

    Value

    Density

    8.00 g/cm3

    Melting Point

    1450 °C

    Modulus of Elasticity

    193 GPa

    Electrical Resistivity

    0.072 x 10-6 Ω.m

    Thermal Conductivity

    16.2 W/m.K

    Thermal Expansion

    17.2 x 10-6 /K

    Alloy Designations

    Stainless steel 304 also corresponds to the following standard designations and specifications:

    Euronorm

    UNS

    BS

    En

    Grade

    1.4301

    S30400

    304S15

    304S16

    304S31

    58E

    304

    1.4306

    S30403

    304S11

    -

    304L

    1.4307

    -

    304S11

    -

    304L

    1.4311

    -

    304S11

    -

    304L

    1.4948

    S30409

    304S51

    -

    304H

    Corrosion Resistance of Stainless Steel 304

    Stainless steel 304
    has excellent corrosion resistance in a wide variety of environments
    and when in contact with different corrosive media. Pitting and crevice
    corrosion can occur in environments containing chlorides. Stress
    corrosion cracking can occur at temperatures over 60°C.

    Heat Resistance of Stainless Steel 304

    Stainless steel 304 has
    good resistance to oxidation in intermittent service up to 870°C and in
    continuous service to 925°C. However, continuous use at 425-860°C is
    not recommended if corrosion resistance in water is required. In this
    instance 304L is recommended due to its resistance to carbide
    precipitation.

    Where high strength is required at temperatures above 500°C and up to
    800°C, grade 304H is recommended. This material will retain aqueous
    corrosion resistance.

    Fabrication of Stainless Steel 304

    Fabrication of all stainless steels should
    be done only with tools dedicated to stainless steel materials. Tooling
    and work surfaces must be thoroughly cleaned before use. These
    precautions are necessary to avoid cross contamination of stainless steel by easily corroded metals that may discolour the surface of the fabricated product.

    Cold Working of Stainless Steel 304

    Stainless steel 304 readily
    work hardens. Fabrication methods involving cold working may require an
    intermediate annealing stage to alleviate work hardening and avoid
    tearing or cracking. At the completion of fabrication a full annealing
    operation should be employed to reduce internal stresses and optimise
    corrosion resistance.

    Hot Working of Stainless Steel 304

    Fabrication methods, like forging, that involve hot working should
    occur after uniform heating to 1149-1260°C. The fabricated components
    should then be rapidly cooled to ensure maximum corrosion resistance.

    Heat Treatment of Stainless Steel 304

    Stainless steel 304 cannot be hardened by heat treatment.

    Solution treatment or annealing can be done by rapid cooling after heating to 1010-1120°C.

    Machinability

    Stainless steel 304 has good machinability. Machining can be enhanced by using the following rules:

    • Cutting edges must be kept sharp. Dull edges cause excess work hardening.

    • Cuts should be light but deep enough to prevent work hardening by riding on the surface of the material.

    • Chip breakers should be employed to assist in ensuring swarf remains clear of the work

    • Low thermal conductivity of austenitic alloys results in heat
      concentrating at the cutting edges. This means coolants and lubricants
      are necessary and must be used in large quantities.

    Welding of Stainless Steel 304

    Fusion welding performance for Stainless steel 304 is excellent both with and without fillers. Recommended filler rods and electrodes for stainless steel 304 is grade 308 stainless steel.
    For 304L the recommended filler is 308L. Heavy welded sections may
    require post-weld annealing. This step is not required for 304L. Grade
    321 may be used if post-weld heat treatment is not possible.

    Applications of Stainless Steel 304

    Stainless steel 304 is typically used in:

    • Sinks and splashbacks

    • Saucepans

    • Cutlery and flatware

    • Architectural panelling

    • Sanitaryware and troughs

    • Tubing

    • Brewery, dairy, food and pharmaceutical production equipment

    • Springs, nuts, bolts and screws

  • Previous:
  • Next:



  • Demonstration of how to braze or solder aluminized stainless steel with a low temperature brazing rod from http://MuggyWeld.com. An aluminum based brazing alloy is necessary when soldering aluminum coated metals such as the stainless pictured in this video.

    Flux is extremely important to aluminum welding or brazing, Super Alloy 5 has weld strength when used on aluminum.

    For more videos and information, or to order, visit http://MuggyWeld.com

    Please read all instructions prior to use at: http://muggyweld.com/packets/superalloy1postsale.pdf
    Pre-cleaning is necessary with Super Alloy 1

    _______________________

    Please visit http://www.aws.org/technical/facts/ prior to using Muggy Weld products, and adhere to all AWS welding safety guidelines. Further product safety information is available at http://muggyweld.com/safety-guidelines.

    Muggy Weld LLC shall not be liable for any loss, injury, claim, liability, or damage of any kind resulting in any way from (a) your use of this Site, (b) any services or products obtained from this Site, (c) any errors in or omissions from this Site, (d) the unavailability or interruption of this Site or any features thereof, (e) any content contained on this Site.

    MSDS sheets available with purchase from MuggyWeld.com, upon request.



    HEY Larlee’s in this video we test out a super expensive mascara wand and the mascara and primer that goes with it. This is the weirdest mascara wand i’ve ever used! The results were very interesting. Yes I bought this product myself I think it’s pretty clear hourglass didn’t send it to me since I didn’t give it a great review….I bought this product to review FOR FUN not because I prefer using $150 mascara! I don’t think $150 for any makeup product is ok regardless of its performance. I hope you enjoyed this video! I hope you guys enjoyed this does it work seris thanks for watching xo- Laura

    WATCH THIS NEXT:
    3D printed lipstick: does it work? https://youtu.be/rh9s4uODnvE
    or
    Branda & Shirley Show: https://youtu.be/lV3sXUwvdgg

    PRODUCTS MENTIONED:
    HOURGLASS The Curator Lash Instrument- http://bit.ly/2dkEUZo
    mascara- http://bit.ly/2crrY74
    primer- http://bit.ly/2debsIP

    SOCIAL MEDIA:
    INSTAGRAM: LARLARLEE
    SNAPCHAT: Laura88lee
    FACEBOOK: Laura Lee
    TWITTER: LAURA88LEE

    D I S C O U N T – C O D E S
    ___________________________________

    Morphe Brushes USE CODE LauraLee for 10% off your total order!

    http://morphebrushes.com

    -SIGMA BEAUTY:

    http://www.sigmabeauty.com/c/1424

    CODE: LAURASIGMA (for 10% off the entire purchase)

    SOCIAL MEDIA:
    INSTAGRAM: LARLARLEE
    SNAPCHAT: Laura88lee
    FACEBOOK: Laura Lee
    TWITTER: LAURA88LEE

    D I S C O U N T – C O D E S
    ___________________________________

    my vanity: http://bit.ly/29z6ZNx
    use code LAURALEE10 for $$ off!!

    Morphe Brushes USE CODE LauraLee for 10% off your total order!

    http://morphebrushes.com

    -SIGMA BEAUTY:

    http://www.sigmabeauty.com/c/1424

    CODE: LAURASIGMA (for 10% off the entire purchase)

    Jouer cosmetics – code: LAURA15OFF
    for 15% off! https://www.jouercosmetics.com

    Ofra Cosmetics use code LAURALEE30 for 30% off!! http://bit.ly/2bm3dGb

    PURcosmetics use code LAURALEE for 20% & FREE SHIPPING!

    http://www.purcosmetics.com/

    music:
    Music Provided by Sync Sync – Need copyright free music for your videos? Sign up here: bit.ly/1NItNJP

    ♡For any business inquiries please email me at: laura88lee@gmail.com

    Like I said in the video as well in the paragraph above I bought it myself no hourglass didn’t send this to me nor did anyone pay me to review this product aka THIS IS NOT SPONSORED enjoy the video xo

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Plane

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the Flag